/* doc/reference.conf - charybdis Example configuration file * * Copyright (C) 2000-2002 Hybrid Development Team * Copyright (C) 2002-2005 ircd-ratbox development team * Copyright (C) 2005-2006 charybdis development team * * Written by ejb, wcampbel, db, leeh and others * */ /* IMPORTANT NOTES: * * class {} blocks MUST be specified before anything that uses them. That * means they must be defined before auth {} and before connect {}. * * auth {} blocks MUST be specified in order of precedence. The first one * that matches a user will be used. So place spoofs first, then specials, * then general access, then restricted. * * privset {} blocks MUST be specified before anything that uses them. That * means they must be defined before operator {}. * * Both shell style (#) and C style comments are supported. * * Files may be included by either: * .include "filename" * .include * * Times/durations are written as: * 12 hours 30 minutes 1 second * * Valid units of time: * month, week, day, hour, minute, second * * Valid units of size: * megabyte/mbyte/mb, kilobyte/kbyte/kb, byte * * Sizes and times may be singular or plural. */ /* Extensions: * * Charybdis contains several extensions that are not enabled by default. * To use them, uncomment the lines below. * * Channel mode +-A (admin only) -- chm_adminonly * Channel mode +-T (blocks notices) -- chm_nonotice * Channel mode +-O (oper only) -- chm_operonly * Channel mode +-S (ssl only) -- chm_sslonly * Emulates channel mode +-O (oper only) (+-iI $o) -- chm_operonly_compat * Emulates channel mode +-R (quiet unreg) (+-q $~a) -- chm_quietunreg_compat * Emulates channel mode +-S (ssl only) (+-b $~z) -- chm_sslonly_compat * Channel mode +-M (disallow KICK on IRC ops) -- chm_operpeace * Restrict channel creation to logged in users -- createauthonly * Account bans (+b $a[:mask]) -- extb_account * Banned from another channel (+b $j:mask) -- extb_canjoin * Other-channel bans (+b $c:mask) -- extb_channel * Combination extbans -- extb_combi * Extended ban (+b $x:mask) -- extb_extgecos * Hostmask bans (for combination extbans) -- extb_hostmask * Oper bans (+b $o) -- extb_oper * Realname (gecos) bans (+b $r:mask) -- extb_realname * Server bans (+b $s:mask) -- extb_server * SSL bans (+b $z) -- extb_ssl * User mode bans (+b $u:modes) -- extb_usermode * Helpops system (umode +H) -- helpops * HURT system -- hurt * New host mangling (umode +x) -- ip_cloaking_4.0 * Old host mangling (umode +h) -- ip_cloaking * Dynamically extend channel limits -- m_extendchans * Find channel forwards -- m_findforwards * /identify support -- m_identify * /locops support -- m_locops * Opers cannot be invisible (umode +i) -- no_oper_invis * Far connection notices (snomask +F) -- sno_farconnect * Remote k/d/x line active notices -- sno_globalkline * Remote oper up notices -- sno_globaloper * Global nick-change notices -- sno_globalnickchange * /whois notifications (snomask +W) -- sno_whois * Oper-override (modehacking only) -- override * Stop services kills -- no_kill_services */ #loadmodule "extensions/chm_adminonly"; #loadmodule "extensions/chm_nonotice"; #loadmodule "extensions/chm_operonly"; #loadmodule "extensions/chm_sslonly"; #loadmodule "extensions/chm_operonly_compat"; #loadmodule "extensions/chm_quietunreg_compat"; #loadmodule "extensions/chm_sslonly_compat"; #loadmodule "extensions/chm_operpeace"; #loadmodule "extensions/createauthonly"; #loadmodule "extensions/extb_account"; #loadmodule "extensions/extb_canjoin"; #loadmodule "extensions/extb_channel"; #loadmodule "extensions/extb_combi"; #loadmodule "extensions/extb_extgecos"; #loadmodule "extensions/extb_hostmask"; #loadmodule "extensions/extb_oper"; #loadmodule "extensions/extb_realname"; #loadmodule "extensions/extb_server"; #loadmodule "extensions/extb_ssl"; #loadmodule "extensions/extb_usermode"; #loadmodule "extensions/helpops"; #loadmodule "extensions/hurt"; #loadmodule "extensions/ip_cloaking_4.0"; #loadmodule "extensions/ip_cloaking"; #loadmodule "extensions/m_extendchans"; #loadmodule "extensions/m_findforwards"; #loadmodule "extensions/m_identify"; #loadmodule "extensions/m_locops"; #loadmodule "extensions/no_oper_invis"; #loadmodule "extensions/sno_farconnect"; #loadmodule "extensions/sno_globalkline"; #loadmodule "extensions/sno_globalnickchange"; #loadmodule "extensions/sno_globaloper"; #loadmodule "extensions/sno_whois"; #loadmodule "extensions/override"; #loadmodule "extensions/no_kill_services"; /* serverinfo {}: Contains information about the server. (OLD M:) */ serverinfo { /* name: the name of our server */ name = "hades.arpa"; /* sid: the unique server id of our server. This must be three * characters long. The first character must be a digit [0-9], the * remaining two chars may be letters [A-Z] or digits [0-9]. * * This parameter must be specified for the server to start. */ sid = "42X"; /* description: the description of our server. '[' and ']' may not * be used here for compatibility with older servers. */ description = "charybdis test server"; /* network info: the name and description of the network this server * is on. Shown in the 005 reply and used with serverhiding. */ network_name = "MyNet"; /* vhost: the IP to bind to when we connect outward to ipv4 servers. * This should be an ipv4 IP only. */ #vhost = "192.0.2.6"; /* vhost6: the IP to bind to when we connect outward to ipv6 servers. * This should be an ipv6 IP only. */ #vhost6 = "2001:db7:2::6"; /* ssl_cert: certificate (and optionally key) for our ssl server */ ssl_cert = "etc/ssl.pem"; /* ssl_private_key: our ssl private key (if not contained in ssl_cert file) */ #ssl_private_key = "etc/ssl.key"; /* ssl_dh_params: DH parameters, generate with openssl dhparam -out dh.pem 2048 */ /* If you do not provide parameters, some TLS backends will fail on DHE- ciphers, and some will succeed but use weak, common DH groups! */ ssl_dh_params = "etc/dh.pem"; /* ssl_cipher_list: A list of ciphers, dependent on your TLS backend */ #ssl_cipher_list = "EECDH+HIGH:EDH+HIGH:HIGH:!aNULL"; /* ssld_count: number of ssld processes you want to start, if you * have a really busy server, using N-1 where N is the number of * cpu/cpu cores you have might be useful. A number greater than one * can also be useful in case of bugs in ssld and because ssld needs * two file descriptors per SSL connection. */ ssld_count = 1; /* default max clients: the default maximum number of clients * allowed to connect. This can be changed once ircd has started by * issuing: * /quote set maxclients */ default_max_clients = 1024; /* nicklen: enforced nickname length (for this server only; must not * be longer than the maximum length set while building). */ nicklen = 30; }; /* admin {}: contains admin information about the server. (OLD A:) */ admin { name = "Smurf target"; description = "Main Server Administrator"; email = ""; }; /* log {}: contains information about logfiles. */ log { /* logfiles: the logfiles to use for specific activity. if these * paths are defined, then ircd will log to them, otherwise it wont. * * The confs are, in order: * - userlog: user exits * - fuserlog: failed user connections * - operlog: /oper usage * - foperlog: failed /oper usage * - serverlog: server connects/disconnects * - klinelog: klines, etc * - killlog: kills * - operspylog: operspy usage * - ioerrorlog: IO errors */ fname_userlog = "logs/userlog"; #fname_fuserlog = "logs/fuserlog"; fname_operlog = "logs/operlog"; #fname_foperlog = "logs/foperlog"; fname_serverlog = "logs/serverlog"; #fname_klinelog = "logs/klinelog"; fname_killlog = "logs/killlog"; fname_operspylog = "logs/operspylog"; #fname_ioerrorlog = "logs/ioerror"; }; /* class {}: contain information about classes for users (OLD Y:) */ class "users" { /* class name must go above */ /* ping time: how often a client must reply to a PING from the * server before they are dropped. */ ping_time = 2 minutes; /* number per ident: the number of users per user@host networkwide * allowed to connect. Unidented connections are classified as * the same ident. */ number_per_ident = 2; /* number per ip: the number of local users per host allowed */ number_per_ip = 3; /* number per ip global: the number of network wide connections * per host allowed for a user, including connections to the * local server. */ number_per_ip_global = 5; /* cidr_ipv4_bitlen: Limits numbers of connections from a subnet size */ cidr_ipv4_bitlen = 24; /* cidr_ipv6_bitlen: Limits numbers of connections from a subnet size * the following example makes the subnet /64 this is useful * for IPv6 connections in particular */ cidr_ipv6_bitlen = 64; /* number_per_cidr: Number of connections to allow from a subnet of the * size given in cidr_ipv4_bitlen/cidr_ipv6_bitlen. * 4 seems to be a good default to me. */ number_per_cidr = 4; /* max number: the maximum number of users allowed in this class */ max_number = 100; /* sendq: the amount of data allowed in a clients queue before * they are dropped. */ sendq = 100 kbytes; }; class "restricted" { ping_time = 1 minute 30 seconds; number_per_ip = 1; max_number = 100; sendq = 60kb; }; class "opers" { ping_time = 5 minutes; number_per_ip = 10; max_number = 100; sendq = 100kbytes; }; class "server" { ping_time = 5 minutes; /* connectfreq: only used in server classes. specifies the delay * between autoconnecting to servers. */ connectfreq = 5 minutes; /* max number: the amount of servers to autoconnect to. if the number * of servers in the class is or exceeds this, no more servers in the * class are autoconnected. oper initiated connects are unaffected. * this should usually be set to either 0 or 1. (autoconnecting from * hubs to leaves may cause leaves to function as hubs by having * multiple servers connected to them.) */ max_number = 1; /* sendq: servers need a higher sendq as they are sent more data */ sendq = 2 megabytes; }; /* listen {}: contain information about the ports ircd listens on (OLD P:) */ listen { /* defer_accept: wait for clients to send IRC handshake data before * accepting them. if you intend to use software which depends on the * server replying first, such as BOPM, you should disable this feature. * otherwise, you probably want to leave it on. */ defer_accept = yes; /* port: the specific port to listen on. if no host is specified * before, it will listen on all available IPs. * * sslport: the specific port to listen ssl connections on. if no * host is specified before, it will listen on all available IPs. * * ports are seperated via a comma, a range may be specified using ".." */ /* port: listen on all available IPs, ports 5000 and 6665 to 6669 */ port = 5000, 6665 .. 6669; /* sslport: listen for ssl connections on all available IPs, port 6697 */ sslport = 6697; /* host: set a specific IP/host the ports after the line will listen * on. This may be ipv4 or ipv6. */ host = "192.0.2.6"; port = 7000, 7001; sslport = 9000, 9001; host = "2001:db8:2::6"; port = 7002; sslport = 9002; /* wsock: listeners defined with this option enabled will be websocket listeners, * and will not accept normal clients. */ wsock = yes; sslport = 9999; }; /* auth {}: allow users to connect to the ircd (OLD I:) */ auth { /* user: the user@host allowed to connect. Multiple IPv4/IPv6 user * lines are permitted per auth block. This is matched against the * hostname and IP address (using :: shortening for IPv6 and * prepending a 0 if it starts with a colon) and can also use CIDR * masks. */ user = "*@198.51.100.0/24"; user = "*test@2001:db8:1:*"; /* auth_user: This allows specifying a username:password instead of * just a password in PASS, so that a fixed user@host is not * necessary for a specific auth{} block. */ #auth_user = "SomeUser"; /* password: an optional password that is required to use this block. * By default this is not encrypted, specify the flag "encrypted" in * flags = ...; below if it is. */ password = "letmein"; /* spoof: fake the users user@host to be be this. You may either * specify a host or a user@host to spoof to. This is free-form, * just do everyone a favour and dont abuse it. (OLD I: = flag) */ spoof = "I.still.hate.packets"; /* Possible flags in auth: * * encrypted | password is encrypted with mkpasswd * spoof_notice | give a notice when spoofing hosts * exceed_limit (old > flag) | allow user to exceed class user limits * kline_exempt (old ^ flag) | exempt this user from k/g/xlines, * | dnsbls, and proxies * dnsbl_exempt | exempt this user from dnsbls * proxy_exempt | exempt this user from proxies * spambot_exempt | exempt this user from spambot checks * shide_exempt | exempt this user from serverhiding * jupe_exempt | exempt this user from generating * warnings joining juped channels * resv_exempt | exempt this user from resvs * flood_exempt | exempt this user from flood limits * USE WITH CAUTION. * no_tilde (old - flag) | don't prefix ~ to username if no ident * need_ident (old + flag) | require ident for user in this class * need_ssl | require SSL/TLS for user in this class * need_sasl | require SASL id for user in this class * extend_chans | allow this user to join more channels than normal */ flags = kline_exempt, exceed_limit; /* class: the class the user is placed in */ class = "opers"; }; auth { /* redirect: the server and port to redirect a user to. A user does * not have to obey the redirection, the ircd just suggests to them * an alternative server. */ redirserv = "irc.example.net"; redirport = 6667; user = "*.example.com"; /* class: a class is required even though it is not used */ class = "users"; }; auth { user = "*@*"; class = "users"; }; /* privset{}: defines operator privilege sets. */ privset "local_op" { /* privs: controls the activities and commands an oper is * allowed to do on the server * * Available options: * * oper:local_kill: allows local users to be /KILL'd * oper:global_kill: allows local and remote users to be /KILL'd * oper:routing: allows remote SQUIT and CONNECT * oper:kline: allows KLINE and DLINE * oper:unkline: allows UNKLINE and UNDLINE * snomask:nick_changes: allows oper to see nickchanges via snomask +n * oper:rehash: allows oper to REHASH config * oper:die: allows DIE and RESTART * oper:admin: gives admin privileges. admins * may (un)load modules and see various * additional information. * oper:hidden_admin: gives admin privileges except * will not have the admin lines in * whois. * oper:xline: allows use of /quote xline/unxline * oper:resv: allows /quote resv/unresv and cmode +LP * oper:operwall: allows the oper to send/receive operwalls * oper:spy: allows 'operspy' features to see through +s * channels etc. see /quote help operspy * oper:hidden: hides the oper from /stats p * oper:remoteban: allows remote kline etc * oper:mass_notice: allows sending wallops and mass notices * oper:grant: allows using the GRANT command */ privs = oper:local_kill, oper:operwall; }; privset "server_bot" { /* extends: a privset to inherit in this privset */ extends = "local_op"; privs = oper:kline, oper:remoteban, snomask:nick_changes; }; privset "global_op" { extends = "local_op"; privs = oper:global_kill, oper:routing, oper:kline, oper:unkline, oper:xline, oper:resv, oper:mass_notice, oper:remoteban; }; privset "admin" { extends = "global_op"; privs = oper:admin, oper:die, oper:rehash, oper:spy, oper:grant; }; /* operator {}: defines ircd operators. (OLD O:) */ operator "god" { /* name: the name of the oper must go above */ /* user: the user@host required for this operator. CIDR *is* * supported now. auth{} spoofs work here, other spoofs do not. * multiple user="" lines are supported. */ user = "*god@*"; user = "*@127.0.0.1"; /* password: the password required to oper. Unless ~encrypted is * contained in flags = ...; this will need to be encrypted using * mkpasswd, MD5 is supported */ password = "etcnjl8juSU1E"; /* rsa key: the public key for this oper when using Challenge. * A password should not be defined when this is used, see * doc/challenge.txt for more information. */ #rsa_public_key_file = "/usr/local/ircd/etc/oper.pub"; /* fingerprint: if specified, the oper's client certificate * fingerprint will be checked against the specified fingerprint * below. */ #fingerprint = "c77106576abf7f9f90cca0f63874a60f2e40a64b"; /* umodes: the specific umodes this oper gets when they oper. * If this is specified an oper will not be given oper_umodes * These are described above oper_only_umodes in general {}; */ #umodes = locops, servnotice, operwall, wallop; /* snomask: specific server notice mask on oper up. * If this is specified an oper will not be given oper_snomask. */ snomask = "+Zbfkrsuy"; /* flags: misc options for the operator. You may prefix an option * with ~ to disable it, e.g. ~encrypted. * * Default flags are encrypted. * * Available options: * * encrypted: the password above is encrypted [DEFAULT] * need_ssl: must be using SSL/TLS to oper up */ flags = encrypted; /* privset: privileges set to grant */ privset = "admin"; }; /* connect {}: controls servers we connect to (OLD C:, N:, H:, L:) */ connect "irc.uplink.com" { /* the name must go above */ /* host: the host or IP to connect to. If a hostname is used it * must match the reverse dns of the server. */ host = "203.0.113.3"; /* vhost: the host or IP to bind to for this connection. If this * is not specified, the default vhost (in serverinfo {}) is used. */ #vhost = "192.0.2.131"; /* passwords: the passwords we send (OLD C:) and accept (OLD N:). * The remote server will have these passwords reversed. */ send_password = "password"; accept_password = "anotherpassword"; /* fingerprint: if specified, the server's client certificate * fingerprint will be checked against the specified fingerprint * below. */ #fingerprint = "c77106576abf7f9f90cca0f63874a60f2e40a64b"; /* port: the port to connect to this server on */ port = 6666; /* hub mask: the mask of servers that this server may hub. Multiple * entries are permitted */ hub_mask = "*"; /* leaf mask: the mask of servers this server may not hub. Multiple * entries are permitted. Useful for forbidding EU -> US -> EU routes. */ #leaf_mask = "*.uk"; /* class: the class this server is in */ class = "server"; /* flags: controls special options for this server * encrypted - marks the accept_password as being crypt()'d * autoconn - automatically connect to this server * compressed - compress traffic via ziplinks * topicburst - burst topics between servers * ssl - ssl/tls encrypted server connections */ flags = compressed, topicburst; }; connect "ipv6.lame.server" { host = "192.0.2.1"; host = "2001:db8:3::8"; send_password = "password"; accept_password = "password"; port = 6666; /* aftype: controls whether the outgoing connection uses "ipv4" or "ipv6". * Default is to try either at random. */ aftype = ipv6; class = "server"; }; connect "ssl.uplink.com" { /* Example of ssl server-to-server connection, ssl flag doesn't need * compressed flag, 'cause it uses own compression */ host = "203.0.113.129"; send_password = "password"; accept_password = "anotherpassword"; port = 9999; hub_mask = "*"; class = "server"; flags = ssl, topicburst; }; /* cluster {}; servers that we propagate things to automatically. * NOTE: This does NOT grant them privileges to apply anything locally, * you must add a seperate shared block for that. Clustering will * only be done for actions by LOCAL opers, that arent directed * remotely. */ cluster { /* name: the server to share with, this can be a wildcard and may be * stacked. */ /* flags: list of what to share, all the name lines above this (up * until another flags entry) will receive these flags. * * kline - share perm klines * tkline - share temp klines * unkline - share unklines * locops - share locops * xline - share perm xlines * txline - share temp xlines * unxline - share unxlines * resv - share perm resvs * tresv - share temp resvs * unresv - share unresvs * all - share all of the above */ /* share klines/unklines/xlines with *.lan */ name = "*.lan"; flags = kline, unkline, xline; /* share locops with irc.ircd-ratbox.org and ircd.ircd-ratbox.org */ name = "irc.ircd-ratbox.org"; name = "ircd.ircd-ratbox.org"; flags = locops; }; /* service{}: privileged servers (services). These servers have extra * privileges such as setting login names on users and introducing clients * with umode +S (unkickable, hide channels, etc). This does not allow them * to set bans, you need a separate shared{} for that. * Do not place normal servers here. * There may be only one service{} block. */ service { /* name: the server name. These may be stacked. */ name = "services.int"; }; /* shared {}: users that are allowed to place remote bans on our server. * NOTE: These are ordered top down. The first one the user@host and server * matches will be used. Their access will then be decided on that * block and will not fall back to another block that matches. */ shared { /* oper: the user@host and server the user must be on to set klines. * The first field must be a user@host, the second field is an * optional server. These may be stacked. */ /* flags: list of what to allow them to place, all the oper lines * above this (up until another flags entry) will receive these * flags. This *must* be present. * * kline - allow setting perm/temp klines * tkline - allow setting temp klines * unkline - allow removing klines * xline - allow setting perm/temp xlines * txline - allow setting temp xlines * unxline - allow removing xlines * resv - allow setting perm/temp resvs * tresv - allow setting temp resvs * unresv - allow removing xlines * all - allow oper/server to do all of above. * locops - allow locops - only used for servers who cluster * rehash - allow rehashing * dline - allow setting perm/temp dlines * tdline - allow setting temp dlines * undline - allow removing dlines * grant - allow granting operator status * die - allow remote DIE/RESTART * module - allow remote module commands * none - disallow everything */ /* allow flame@*.leeh.co.uk on server irc.ircd-ratbox.org and * allow leeh@*.leeh.co.uk on server ircd.ircd-ratbox.org to kline */ oper = "flame@*.leeh.co.uk", "irc.ircd-ratbox.org"; oper = "leeh@*.leeh.co.uk", "ircd.ircd-ratbox.org"; flags = kline; /* you may forbid certain opers/servers from doing anything */ oper = "irc@vanity.oper", "*"; oper = "*@*", "irc.vanity.server"; oper = "irc@another.vanity.oper", "bigger.vanity.server"; flags = none; /* or allow everyone to place temp klines */ oper = "*@*"; flags = tkline; }; /* exempt {}: IPs that are exempt from Dlines and rejectcache. (OLD d:) */ exempt { ip = "192.0.2.0/24"; /* these may be stacked */ ip = "127.0.0.1"; }; /* The channel block contains options pertaining to channels */ channel { /* invex: Enable/disable channel mode +I, a n!u@h list of masks * that can join a +i channel without an invite. */ use_invex = yes; /* except: Enable/disable channel mode +e, a n!u@h list of masks * that can join a channel through a ban (+b). */ use_except = yes; /* forward: Enable/disable channel mode +f, a channel to forward * users to if they can't join because of +i etc. Also enables ban * forwarding, $. */ use_forward = yes; /* knock: Allows users to request an invite to a channel that * is locked somehow (+ikl). If the channel is +p or you are banned * the knock will not be sent. */ use_knock = yes; /* knock delay: The amount of time a user must wait between issuing * the knock command. */ knock_delay = 5 minutes; /* knock channel delay: How often a knock to any specific channel * is permitted, regardless of the user sending the knock. */ knock_delay_channel = 1 minute; /* max chans: The maximum number of channels a user can join/be on. */ max_chans_per_user = 15; /* max chans (large): The extended maximum number of channels a user can join. */ max_chans_per_user_large = 60; /* max bans: maximum number of +b/e/I/q modes in a channel */ max_bans = 100; /* max bans: maximum number of +b/e/I/q modes in a +L channel */ max_bans_large = 500; /* splitcode: split users, split servers and either no join on split * or no create on split must be enabled for split checking. * splitmode will be entered on either split users or split servers * dropping below the limit. * * you may force splitmode to be permanent by /quote set splitmode on */ /* split users: when the usercount is lower than this level, consider * ourselves split. this must be set for automatic splitmode */ default_split_user_count = 0; /* split servers: when the amount of servers that have acknowledged * theyve finished bursting is lower than this, consider ourselves * split. this must be set for automatic splitmode */ default_split_server_count = 0; /* split: no create: disallow users creating channels on split */ no_create_on_split = no; /* split: no join: disallow users joining channels at all on a split */ no_join_on_split = no; /* burst topicwho: when bursting topics, also burst the topic setter */ burst_topicwho = yes; /* kick on split riding: kick users riding splits to join +i or +k * channels. more precisely, if a bursting server sends an SJOIN * for a channel with a lower TS with either a +i mode or a +k * mode with a different key, kick all local users. * * note: this does not take +r, +b, +e and +I into account. */ kick_on_split_riding = no; /* only ascii channels: disable local users joining channels * containing characters outside the range 33-126 (non-printable * or non-ASCII). */ only_ascii_channels = no; /* resv_forcepart: force any local users to part a channel * when a RESV is issued. */ resv_forcepart = yes; /* channel target change: restrict how many channels users can * message per unit of time. IRC operators, channel operators and * voiced users are exempt. */ channel_target_change = yes; /* disable local channels: if yes, then local channels will not be * supported. */ disable_local_channels = no; /* autochanmodes: the channel modes that should be automatically set * when a channel is created. */ autochanmodes = "+nt"; /* displayed_usercount: the minimum amount of users on a channel before it * is displayed in LIST. this parameter can be overridden using ELIST parameters, * such as LIST >0. */ displayed_usercount = 3; /* strip_topic_colors: whether or not color codes in TOPIC should be stripped. */ strip_topic_colors = no; }; /* The serverhide block contains the options regarding serverhiding */ serverhide { /* flatten links: this option will hide various routing information * and make all servers in /links appear that they are linked to * this server. */ flatten_links = no; /* links delay: how long to wait before showing splits or new * servers in a flattened /links output. */ links_delay = 5 minutes; /* hidden: hide this server from a /links output on servers with * flatten_links enabled. this allows hub servers to be hidden etc. */ hidden = no; /* disable hidden: prevent servers hiding themselves from a * /links ouput. */ disable_hidden = no; }; /* These are the blacklist settings. * You can have multiple combinations of host and rejection reasons. * They are used in pairs of one host/rejection reason. * * These settings should be adequate for most networks. * * Word to the wise: Do not use blacklists like SPEWS for blocking IRC * connections. * * As of charybdis 2.2, you can do some keyword substitution on the rejection * reason. The available keyword substitutions are: * * ${ip} - the user's IP * ${host} - the user's canonical hostname * ${dnsbl-host} - the dnsbl hostname the lookup was done against * ${nick} - the user's nickname * ${network-name} - the name of the network * * As of charybdis 3.4, a type parameter is supported, which specifies the * address families the blacklist supports. IPv4 and IPv6 are supported. * IPv4 is currently the default as few blacklists support IPv6 operation * as of this writing. * * As of charybdis 3.5, a matches parameter is allowed; if omitted, any result * is considered a match. If included, a comma-separated list of *quoted* * strings is allowed to match queries. They may be of the format "0" to "255" * to match the final octet (e.g. 127.0.0.1) or "127.x.y.z" to explicitly match * an A record. The blacklist is only applied if it matches anything in the * list. You may freely mix full IP's and final octets. * * Consult your blacklist provider for the meaning of these parameters; they * are usually used to denote different ban types. */ blacklist { host = "rbl.efnetrbl.org"; type = ipv4; reject_reason = "${nick}, your IP (${ip}) is listed in EFnet's RBL. For assistance, see http://efnetrbl.org/?i=${ip}"; /* Example of a blacklist that supports both IPv4 and IPv6 and using matches */ # host = "foobl.blacklist.invalid"; # matches = "4", "6", "127.0.0.10"; # type = ipv4, ipv6; # reject_reason = "${nick}, your IP (${ip}) is listed in ${dnsbl-host} for some reason. In order to protect ${network-name} from abuse, we are not allowing connections listed in ${dnsbl-host} to connect"; }; /* These are the OPM settings. * This is similar to the functionality provided by BOPM. It will scan incoming * connections for open proxies by connecting to clients and attempting several * different open proxy handshakes. If they connect back to us (via a dedicated * listening port), and send back the data we send them, they are considered * an open proxy. For politeness reasons (users may be confused by the incoming * connection attempts if they are logging incoming connections), the user is * notified upon connect if they are being scanned. * * WARNING: * These settings are considered experimental. Only the most common proxy types * are checked for (Charybdis is immune from POST and GET proxies). If you are * not comfortable with experimental code, remove or comment out the *entire* * block below to disable the proxy scanner. */ opm { /* IPv4 address to listen on. This must be a publicly facing IP address * to be effective. * If omitted, it defaults to serverinfo::vhost. */ #listen_ipv4 = "127.0.0.1"; /* IPv4 port to listen on. * This should not be the same as any existing listeners. */ #port_ipv4 = 32000; /* IPv6 address to listen on. This must be a publicly facing IP address * to be effective. * If omitted, it defaults to serverinfo::vhost6. */ #listen_ipv6 = "::1"; /* IPv6 port to listen on. * This should not be the same as any existing listeners. */ #port_ipv6 = 32000; /* You can also set the listen_port directive which will set both the * IPv4 and IPv6 ports at once. */ listen_port = 32000; /* This sets the timeout in seconds before ending open proxy scans. * Values less than 1 or greater than 60 are ignored. * It is advisable to keep it as short as feasible, so clients do not * get held up by excessively long scan times. */ timeout = 5; /* These are the ports to scan for SOCKS4 proxies on. They may overlap * with other scan types. Sensible defaults are given below. */ socks4_ports = 80, 443, 1080, 8000, 8080, 10800; /* These are the ports to scan for SOCKS5 proxies on. They may overlap * with other scan types. Sensible defaults are given below. */ socks5_ports = 80, 443, 1080, 8000, 8080, 10800; /* These are the ports to scan for HTTP CONNECT proxies on (plaintext). * They may overlap with other scan types. Sensible defaults are given * below. */ httpconnect_ports = 80, 8080, 8000; /* These are the ports to scan for HTTPS CONNECT proxies on (SSL). * They may overlap with other scan types. Sensible defaults are given * below. */ httpsconnect_ports = 443, 4443; }; /* * Alias blocks allow you to define custom commands. (Old m_sshortcut.c) * They send PRIVMSG to the given target. A real command takes * precedence above an alias. */ alias "NickServ" { /* the name must go above */ /* target: the target nick (must be a network service) or * user@server (cannot be this server, only opers can use * user starting with "opers" reliably, interpreted on the target * server only so you may need to use nick@server instead) */ target = "NickServ"; }; alias "ChanServ" { target = "ChanServ"; }; alias "OperServ" { target = "OperServ"; }; alias "MemoServ" { target = "MemoServ"; }; alias "NS" { target = "NickServ"; }; alias "CS" { target = "ChanServ"; }; alias "OS" { target = "OperServ"; }; alias "MS" { target = "MemoServ"; }; /* The general block contains many of the options that were once compiled * in options in config.h. The general block is read at start time. */ general { /* hide error messages: defines whether error messages from * servers that are not deemed fully safe are hidden or not. * These can sometimes contain IPs and can have an adverse * effect on server ip hiding. Set to: * yes: hide from opers and admin * opers: hide from opers only * no: do not hide error messages * Admins on other servers count as opers. */ hide_error_messages = opers; /* hide spoof ips: hide the real ips of auth{} spoofed users * If disabled, local opers can see them. * Dynamic spoofs (e.g. set by services) are unaffected by this; * any oper (local and remote) can see the real ip. */ hide_spoof_ips = yes; /* default umodes: umodes to set upon connection * If you have enabled the ip_cloaking extension, and you wish for * incoming clients to be set +h or +x upon connection, add +h or +x to the umode * string below. */ default_umodes = "+i"; /* default operstring: defines the default oper response * in /whois queries, eg "is an IRC Operator". * After startup use /quote set operstring to change. */ default_operstring = "is an IRC Operator"; /* default adminstring: defines the default admin response * in /whois queries, eg "is a Server Administrator". * After startup use /quote set adminstring to change. */ default_adminstring = "is a Server Administrator"; /* servicestring: defines the response for opered services (+S) * in /whois queries, eg "is a Network Service". * This is updated on rehash. */ servicestring = "is a Network Service"; /* * Nick of the network's SASL agent. Used to check whether services are here, * SASL credentials are only sent to its server. Needs to be a service. * * Defaults to SaslServ if unspecified. */ sasl_service = "SaslServ"; /* disable fake channels: disable local users joining fake versions * of channels, eg #foo^B^B. Disables bold, mirc colour, reverse, * underline and hard space. (ASCII 2, 3, 22, 31, 160 respectively). */ disable_fake_channels = no; /* tkline_expire_notices: give a notice to opers when a tkline * expires */ tkline_expire_notices = no; /* floodcount: the default value of floodcount that is configurable * via /quote set floodcount. This is the amount of lines a user * may send to any other user/channel in one second. */ default_floodcount = 10; /* failed oper notice: send a notice to all opers on the server when * someone tries to OPER and uses the wrong password, host or ident. */ failed_oper_notice = yes; /* dots in ident: the amount of '.' characters permitted in an ident * reply before the user is rejected. */ dots_in_ident = 2; /* min nonwildcard: the minimum non wildcard characters in k/d/g lines * placed via the server. klines hand placed are exempt from limits. * wildcard chars: '.' '*' '?' '@' */ min_nonwildcard = 4; /* min nonwildcard simple: the minimum non wildcard characters in * xlines/resvs placed via the server. * wildcard chars: '*' '?' */ min_nonwildcard_simple = 3; /* max accept: maximum allowed /accept's for +g usermode */ max_accept = 20; /* max monitor: the maximum amount of nicknames a client may have in * their monitor (server-side notify) list. */ max_monitor = 100; /* nick flood: enable the nickflood control code */ anti_nick_flood = yes; /* nick flood: the nick changes allowed in the specified period */ max_nick_time = 20 seconds; max_nick_changes = 5; /* anti spam time: the minimum time a user must be connected before * custom quit messages are allowed. */ anti_spam_exit_message_time = 5 minutes; /* ts delta: the time delta allowed between server clocks before * a warning is given, or before the link is dropped. all servers * should run ntpdate/rdate to keep clocks in sync */ ts_warn_delta = 30 seconds; ts_max_delta = 5 minutes; /* client exit: prepend a user's quit message with "Quit: " */ client_exit = yes; /* collision fnc: change user's nick to their UID instead of * killing them, if possible. This setting only applies to nick * collisions detected on this server. Only enable this if * all servers on the network allow remote nicks to start with * a digit. */ collision_fnc = yes; /* resv fnc: change a user's nick to a nick they have recently used * (or their UID, if no such nick can be found) when a resv matching * them is set by services. Only enable this if all servers on the * network allow remote nicks to start with a digit. */ resv_fnc = yes; /* global snotices: send out certain snotices (most +b, +f, +y, * some +s) to other servers via ENCAP SNOTE. Received SNOTEs are * displayed unconditionally. */ global_snotices = yes; /* dline reason: show the user the dline reason when they connect * and are dlined. */ dline_with_reason = yes; /* kline delay: delay the checking of klines until a specified time. * Useful if large kline lists are applied often to prevent the * server eating CPU. */ kline_delay = 0 seconds; /* kline reason: show the user the reason why they are k/dlined * on exit. may give away who set k/dline when set via tcm. */ kline_with_reason = yes; /* kline reason: make the users quit message on channels this * reason instead of the oper's reason. */ kline_reason = "Connection closed"; /* identify to services via server password * if auth{} block had no password but the user specified a * server password anyway, send a PRIVMSG to * with as text . */ identify_service = "NickServ@services.int"; identify_command = "IDENTIFY"; /* non redundant klines: flag and ignore redundant klines */ non_redundant_klines = yes; /* warn no nline: warn opers about servers that try to connect but * we dont have a connect {} block for. Twits with misconfigured * servers can get really annoying with this enabled. */ warn_no_nline = yes; /* use propagated bans: KLINE, XLINE and RESV set fully propagated bans. * That means the bans are part of the netburst and restarted/split * servers will get them, but they will not apply to 3.2 and older * servers at all. */ use_propagated_bans = yes; /* stats e disabled: disable stats e. useful if server ips are * exempted and you dont want them listing on irc. */ stats_e_disabled = no; /* stats c oper only: make stats c (connect {}) oper only */ stats_c_oper_only = no; /* stats h oper only: make stats h (hub_mask/leaf_mask) oper only */ stats_h_oper_only = no; /* stats y oper only: make stats y (class {}) oper only */ stats_y_oper_only = no; /* stats o oper only: make stats o (opers) oper only */ stats_o_oper_only = yes; /* stats P oper only: make stats P (ports) oper only * NOTE: users doing stats P will never be given the ips that the * server listens on, simply the ports. */ stats_P_oper_only = no; /* stats i oper only: make stats i (auth {}) oper only. set to: * yes: show users no auth blocks, made oper only. * masked: show users first matching auth block * no: show users all auth blocks. */ stats_i_oper_only = masked; /* stats k/K oper only: make stats k/K (klines) oper only. set to: * yes: show users no auth blocks, made oper only * masked: show users first matching auth block * no: show users all auth blocks. */ stats_k_oper_only = masked; /* map oper only: make /map oper only */ map_oper_only = no; /* operspy admin only: make operspy notices to +Z admin only */ operspy_admin_only = no; /* operspy dont care user info: treat /who mask as if there was * an '!' always; do not log or server notice about operspy * /who mask, /masktrace and /scan. channel information is still * protected. */ operspy_dont_care_user_info = no; /* caller id wait: time between notifying a +g user that somebody * is messaging them. */ caller_id_wait = 1 minute; /* pace wait simple: time between use of less intensive commands * (HELP, remote WHOIS, WHOWAS) */ pace_wait_simple = 1 second; /* pace wait: time between more intensive commands * (ADMIN, INFO, LIST, LUSERS, MOTD, STATS, VERSION) */ pace_wait = 10 seconds; /* short motd: send clients a notice telling them to read the motd * instead of forcing a motd to clients who may simply ignore it. */ short_motd = no; /* ping cookies: require clients to respond exactly to a ping command, * can help block certain types of drones and FTP PASV mode spoofing. */ ping_cookie = no; /* connect timeout: sets how long we should wait for a connection * request to succeed */ connect_timeout = 30 seconds; /* ident timeout: Amount of time (in seconds) that the IRCd will * wait for a user to respond to an ident request. */ default_ident_timeout = 5; /* disable auth: disables identd checking */ disable_auth = no; /* no oper flood: increase flood limits for opers. */ no_oper_flood = yes; /* REMOVE ME. The following line checks you've been reading. */ havent_read_conf = yes; /* max targets: the maximum amount of targets in a single * PRIVMSG/NOTICE. set to 999 NOT 0 for unlimited. */ max_targets = 4; /* use_whois_actually: send clients requesting a whois a numeric * giving the real IP of non-spoofed clients to prevent DNS abuse. */ use_whois_actually = yes; /* usermodes configurable: a list of usermodes for the options below * * +g - callerid - Server Side Ignore * +D - deaf - Don't see channel messages * +i - invisible - Not shown in NAMES or WHO unless you share a * a channel * +l - locops - See LOCOPS messages * +Q - noforward - Unaffected by channel forwarding * +R - regonlymsg - No messages from unindentified * +s - servnotice - See server notices * +w - wallop - See oper and server generated WALLOPS * +z - operwall - See operwalls */ /* oper only umodes: usermodes only opers may set */ oper_only_umodes = operwall, locops, servnotice; /* oper umodes: default usermodes opers get when they /oper */ oper_umodes = locops, servnotice, operwall, wallop; /* oper snomask: default snomask opers get when they /oper, * provided they have umode +s set */ oper_snomask = "+s"; /* compression level: level of compression for compressed links between * servers. * * values are between: 1 (least compression, fastest) * and: 9 (most compression, slowest). */ #compression_level = 6; /* burst_away: This enables bursting away messages to servers. * With this disabled, we will only propogate AWAY messages * as users send them, but never burst them. Be warned though * enabling this could increase the size of a burst significantly * for a large network, like EFnet. */ burst_away = yes; /* nick delay: This locks nicks of split clients for the given time * or until a remote client uses the nick. This significantly * reduces nick collisions on short splits but it can be annoying. * To make things as fair as possible, this should be the same on * all servers. If you enable this, the suggested value is 15 minutes. */ nick_delay = 0 seconds; /* reject time: the amount of rejections through klines/dlines etc * allowed in the given time before the rejection is cached and * a pseudo temp dline is placed */ reject_ban_time = 1 minute; reject_after_count = 3; /* reject duration: the amount of time to cache the rejection */ reject_duration = 5 minutes; /* throttle_duration: Amount of time that throttling will be applied to an IP * address. */ throttle_duration = 60; /* throttle_count: Number of connections within throttle_duration that it takes * for throttling to take effect */ throttle_count = 4; /* client flood_max_lines: maximum number of lines in a clients queue before * they are dropped for flooding. */ client_flood_max_lines = 20; /* Flood control settings. DO NOT CHANGE THESE without extensive discussion * and testing by someone who knows exactly what they do. * * These settings replicate charybdis-3.3 behaviour. */ client_flood_burst_rate = 40; client_flood_burst_max = 5; client_flood_message_time = 1; client_flood_message_num = 2; /* max_ratelimit_tokens: the maximum number of ratelimit tokens that one * user can accumulate. This attempts to limit the amount of outbound * bandwidth one user can consume. Do not change unless you know what * you're doing. */ max_ratelimit_tokens = 30; /* away_interval: the minimum interval between AWAY commands. One * additional AWAY command is allowed, and only marking as away * counts. */ away_interval = 30; /* certfp_method: the method that should be used for computing certificate fingerprints. * Acceptable options are sha1, sha256, spki_sha256, sha512 and spki_sha512. Networks * running versions of charybdis prior to charybdis 3.5 MUST use sha1 for certfp_method. * * The spki_* variants operate on the SubjectPublicKeyInfo of the certificate, which does * not change unless the private key is changed. This allows the fingerprint to stay * constant even if the certificate is reissued. These fingerprints will be prefixed with * "SPKI:SHA2-256:" or "SPKI:SHA2-512:" depending on the hash type. These fingerprints * are not supported on servers running charybdis 3.5 or earlier. * * To generate a fingerprint from a certificate file, please use the mkfingerprint utility * program located in the bin/ subdirectory of your IRCd installation. Running it with no * arguments will give you a brief usage message; it takes method and filename arguments. */ certfp_method = spki_sha256; /* hide_opers_in_whois: if set to YES, then oper status will be hidden in /WHOIS output. */ hide_opers_in_whois = no; }; modules { /* module path: paths to search for modules specified below and * in /modload. */ path = "/usr/local/ircd/modules"; path = "/usr/local/ircd/modules/autoload"; /* module: the name of a module to load on startup/rehash */ #module = "some_module"; };